Search:

Type: Posts; User: brett_dirtbike

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    10
    Views
    1,761

    im temporarily quitting this hobby until i get...

    im temporarily quitting this hobby until i get some money again.. i have spent over $300 on this truck in the past 3 months (driving usually 2 times a week, about an hour each time) and i have...
  2. today was a terrible day.. i drove the ERBE...

    today was a terrible day..

    i drove the ERBE for a total of 20 minutes and in that time i broke two rear body mounts, one body, two more driveshafts and tore two tires off the wheel

    after i...
  3. Replies
    10
    Views
    1,761

    alright, today was a terrible day.. i drove...

    alright, today was a terrible day..

    i drove the ERBE for a total of 20 minutes and in that time i broke the pushrod brace i made and destroyed two more rear body mounts, one body, two driveshafts...
  4. i know about unbalanced wheels causing excessive...

    i know about unbalanced wheels causing excessive bearing wear, but driveshaft wear too?

    two of my badlands are kinda out of balance (one has a cracked wheel so it wobbles a bit) and the tires are...
  5. i am also using the extended rear arms, which i...

    i am also using the extended rear arms, which i would blame for the frequent breakages.. but i am breaking all 4 corners pretty much equally.. so i dont think its the rear arms fault

    i am also...
  6. alright, so heres a photo of a typical broken...

    alright, so heres a photo of a typical broken shaft.. as you can see, it only has about 15 minutes on it (it was a rear shaft, hense the roost damage from front tires spraying it with rocks) all 3...
  7. to answer all of you in one post, i have owned my...

    to answer all of you in one post, i have owned my revo since january of 2009, i have gone through about 25 shafts if i were to estimate, plus a ton of u-joints and stub axle yokes

    i had my truck...
  8. badlands mounted on RPM revolvers, or AKA...

    badlands mounted on RPM revolvers, or AKA cityblocks on AKA dishes

    not exactly the heaviest setups, and i dont hammer the throttle really ever, i dont land off jumps with the throttle pinned or...
  9. theres a lot of people on here that claim the...

    theres a lot of people on here that claim the summit shafts are not much stronger than revo shafts.. not worth the money (roughly $80 to convert all 4 shafts)
  10. Replies
    39
    Views
    2,011

    i bought two pro-line hex wrenches.. 2 and 2.5mm...

    i bought two pro-line hex wrenches.. 2 and 2.5mm because those are my most used sizes.. i am very pleased with my purchase so far:D
  11. are there any stronger driveshaft options?

    i came SO close to smashing my e-revo into peices today because im so sick of having to buy replacement driveshafts!! i am using 4s and have my punch control on 80% and slipper set so loose that it...
  12. Replies
    10
    Views
    1,761

    im talking about the body mount, not the wing...

    im talking about the body mount, not the wing mount

    i took a shot at making a brace from the rear shock mount to the top of the rear body mount and it took all the play out of the assembly.. i...
  13. Replies
    10
    Views
    1,761

    aluminum rear body mount

    hey all, im getting tired of replacing my rear body mount each day i run so im looking to upgrading to an aluminum one (STRC in specific).. does anyone have any experience with this part?

    what...
  14. Thread: Wow!

    by brett_dirtbike
    Replies
    11
    Views
    1,678

    badlands will fit on any wheel that is labeled as...

    badlands will fit on any wheel that is labeled as MT size.. so just look for an MT wheel with 17mm hex that you like
  15. Replies
    27
    Views
    4,034

    dont you think you'd be better off making a scale...

    dont you think you'd be better off making a scale raptor if you used a raptor body and not the F150 body??:unsure:
  16. Replies
    12
    Views
    469

    KoolDeal, read this thread:...

    KoolDeal, read this thread: http://monster.traxxas.com/showthread.php?t=525299

    i think you might have gotten your body from the same ebay seller, maybe using cheap remakes of pro-line bodies and...
  17. Replies
    31
    Views
    921

    i broke my left steering block during my 2nd heat...

    i broke my left steering block during my 2nd heat at an LHS race on sunday, put the stock driveshaft and steeting block back on and ran the rest of the day with 3 CVDs and 1 stock driveshaft with no...
  18. Replies
    31
    Views
    921

    ok, mine dont have a grub screw, so they are the...

    ok, mine dont have a grub screw, so they are the newer version?
  19. Replies
    31
    Views
    921

    i bought my tekno cvds from A-Main Hobbies, i...

    i bought my tekno cvds from A-Main Hobbies, i wonder if they'll track me down or even if i have the pre-revision shafts?!
  20. Replies
    173
    Views
    13,192

    +1 on that man.. im sick of breaking my ERBE...

    +1 on that man.. im sick of breaking my ERBE shafts on only 4s!
  21. Replies
    6
    Views
    1,530

    no, but you can screw the bottom pivot ball out a...

    no, but you can screw the bottom pivot ball out a couple turns to give you more camber.. its kinda hard to tune though;)
  22. Replies
    50
    Views
    3,616

    my body was totally ruined after 10 minutes of...

    my body was totally ruined after 10 minutes of practice at my LHS track, i crashed the truck twice, no landing upside down or anything too violent

    i know all about hurting my hands cutting bodies,...
  23. Replies
    50
    Views
    3,616

    well theres my problem, my slipstream was as easy...

    well theres my problem, my slipstream was as easy to cut as the stock body

    maybe i just got a dud? i was so off when it broke on the first run.. $30 and two hours of painting gone in about 10...
  24. Replies
    11
    Views
    2,138

    not exactly, the slash 4x4's wheelbase is about...

    not exactly, the slash 4x4's wheelbase is about 1" shorter, but the e-revo chassis is 2/3 the width of the slash's chassis

    if anything, the slash overtray would be far too large to fit inside the...
  25. Replies
    10
    Views
    484

    i'm sure there is enough material in your AKA...

    i'm sure there is enough material in your AKA adaptors that you could drill them out to 6mm

    stock is 5mm, right? so you're only removing 0.5mm from the wall thickness
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4