Search:

Type: Posts; User: thingsbreak2ez

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    14
    Views
    1,437

    at this point the only things i could think of...

    at this point the only things i could think of would be double check your gear mesh and make sure that you reassembled the slipper clutch properly i.e. make sure that the notch in this...
  2. 1 up on the jato a arm mod. works great,...

    1 up on the jato a arm mod. works great, although i would also recommend sway bars if you do the mod
  3. Replies
    6
    Views
    222

    if the engine is pretty new this will happen...as...

    if the engine is pretty new this will happen...as it becomes more worn in with use it will be easier to pull w/o having to loosen the glow plug
  4. Replies
    11
    Views
    1,269

    are those jato a-arms on the front? i did the...

    are those jato a-arms on the front? i did the same to my rusty a while back and i lost quite a bit of turning radius...did u notice any difference or was it about the same
  5. Replies
    9
    Views
    815

    gear mesh can cause the problem too...and i said...

    gear mesh can cause the problem too...and i said loose as in slightly...if its barely on there then yes it will fall off
  6. the tires wont fit on the stock rims of the older...

    the tires wont fit on the stock rims of the older rustler is what i meant
  7. depends if you have an old rusty or newer...

    depends if you have an old rusty or newer rusty...they wont fit on the old model but on the newer one they should work
  8. Replies
    9
    Views
    815

    check your manual but i think it should b between...

    check your manual but i think it should b between half and 1 turn loose. the slipper pegs create more friction between the clutch and the spur gear. More pegs reduces the slip
  9. Replies
    9
    Views
    815

    it happens when the spur gear nut is too...

    it happens when the spur gear nut is too loose...the slipper slips too much creating excess friction causing the plastic to melt...if it happens a few time the nylon in the nut melts too and it will...
  10. Replies
    10
    Views
    286

    check the connections on the plug between the...

    check the connections on the plug between the batt and esc?
  11. Replies
    9
    Views
    815

    i did this sooo many times when i first got my...

    i did this sooo many times when i first got my truck. Dont just replace the spur gear you need a new nut to hold it on. Once you melt the spur a few times the heat melts the nylon in the nut that...
  12. The surface should be hard enough that you wont...

    The surface should be hard enough that you wont spin out at all.

    I wouldnt do any tuning until you are completely finished with break in.

    You can break the truck in in 40 degree weather and it...
  13. Replies
    30
    Views
    466

    first mod after break in on every traxxas i own:...

    first mod after break in on every traxxas i own: pull start and glo igniter. Soooooooo much easier. no pun intended. but seriously i can consistently get my trucks running in 4-5 pulls when the...
  14. Replies
    5
    Views
    295

    you can get a shorter switch harness, and wrap up...

    you can get a shorter switch harness, and wrap up any extra wire then just use servo tape to attach the switch. and for the back i would take off the battery box and zip tie the easy start wires to...
  15. Replies
    19
    Views
    431

    body reamer, exacto knife, and a drawing compass

    body reamer, exacto knife, and a drawing compass
  16. Replies
    11
    Views
    314

    haha i hardly ever drive with the body on and...

    haha i hardly ever drive with the body on and have never broken a thing due to that. you wont notice much performance difference tho. i just dont use it because if i decide i want to adjust...
  17. Replies
    19
    Views
    521

    definatly agree to straping the tires...run a...

    definatly agree to straping the tires...run a piece of duct tape around the insaide and it will help with both low and high end control a lot
  18. after you finish be careful that the turnbuckle...

    after you finish be careful that the turnbuckle didnt get threaded in a little sideways
  19. you dont have to take the tank off.....tho if you...

    you dont have to take the tank off.....tho if you havent trashed the ez start yet it can be kinda a pain to get your fingers down there to get the fuel line on and off. plus theres a higher risk of...
  20. Replies
    6
    Views
    273

    no it doesnt...the only only thing that should be...

    no it doesnt...the only only thing that should be effected by the smaller tires is less stress on the driveline because there is less rotational mass. you shouldnt have to re-gear though
  21. Replies
    26
    Views
    616

    i was about to get 2 of those, one for my maxx...

    i was about to get 2 of those, one for my maxx project the other for rusty...didnt realize they got discontinued....thats annoying
  22. Replies
    4
    Views
    257

    i have always used the speed hawg tires on my...

    i have always used the speed hawg tires on my rustler for pavement and i love them. even after a long time when they started wearing thin they gripped great
  23. Replies
    6
    Views
    2,142

    have you checked the tune? becuase that could be...

    have you checked the tune? becuase that could be causing it. or the tranny might literally be stuck in 2nd like something is forcing it there...but i have no clue what it could be
  24. Replies
    4
    Views
    255

    i have had good experiances with pro-line road...

    i have had good experiances with pro-line road rage tires for driving on pavement
  25. if the engine in brand new i wouldnt be surprised...

    if the engine in brand new i wouldnt be surprised if part of the problem was the piston stuck at TDC, and the glow plug can be bad even if it has never been used. trust me i have opened brand new...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4