Search:

Type: Posts; User: BuGgYbAsHeR.28

Page 1 of 3 1 2 3

Search: Search took 0.25 seconds.

  1. Replies
    48
    Views
    1,175

    Well here is the finished product! I got a full...

    Well here is the finished product! I got a full run and she did great. I will reduce the pinch control now to 30% since I have the 1/8th conversion complete. Does anyone else disagree with that or...
  2. Mine does the same thing, its due to the bec...

    Mine does the same thing, its due to the bec being wired in the the connection. I have thought about making a switch for it. Wouldn't be hard to do
  3. Replies
    48
    Views
    1,175

    I have them shimmed but need to tweak it a bit...

    I have them shimmed but need to tweak it a bit more, these hyper diffs and the use of the outdrives required so many shims. I shimmed the out drives on either side of the diff by at least an 1/8...
  4. Replies
    45
    Views
    1,510

    Hey man where did you find the braces you are...

    Hey man where did you find the braces you are using to tie together the chassis braces?? Looks like a steering post.
  5. Replies
    48
    Views
    1,175

    I have my diffs in today, I went ahead an ordered...

    I have my diffs in today, I went ahead an ordered some shims, looks like the pinion could be shimmed. It appears like the Traxxas diff, it wants to slam back into the diff. But I hope to have this...
  6. Replies
    48
    Views
    1,175

    Would a aluminum bell crank benefit me in any...

    Would a aluminum bell crank benefit me in any way? Over the plastic one I figured it might eliminate a lot of slop out of the steering system if I went to aluminum.

    Also, would you suggest the...
  7. Replies
    48
    Views
    1,175

    I might try that but for the time being I'll use...

    I might try that but for the time being I'll use what I have which is the lunsgford ti pins. You have the part number for the flm pins with the rpm arms? There site isn't very clear.
  8. Replies
    48
    Views
    1,175

    Ya I have all the other screws and hinge pins in...

    Ya I have all the other screws and hinge pins in a separate bag but it came with those dowels and that long screw which I have no clue where that long screw goes too??


    Secondly, it came with...
  9. Replies
    48
    Views
    1,175

    Okay that's what I figured. Where does that...

    Okay that's what I figured. Where does that screw go? It is way longer than the rest and there is only one.
  10. Replies
    48
    Views
    1,175

    So ya rock-rod those hybrids came with the stubs....

    So ya rock-rod those hybrids came with the stubs. That's a nice lil bonus. I now have 2 questions concerning the bulks.
    ...
  11. Replies
    48
    Views
    1,175

    And also could you list the shims needed for the...

    And also could you list the shims needed for the diff to do a proper shim job rock-rod. Much appreciated bro!
  12. Replies
    19
    Views
    980

    Could you list the shims you used to do the diffs...

    Could you list the shims you used to do the diffs and possibly where I could get them?? Thanks bro!
  13. Replies
    19
    Views
    980

    Ya same here. What diff's did you end up with in...

    Ya same here. What diff's did you end up with in this truck mcly?
  14. Replies
    48
    Views
    1,175

    I'm not sure I just ordered them last night off...

    I'm not sure I just ordered them last night off eBay, guy only has a few left for those looking for them now. I should have those this weekend and hopefully they do like yours did!


    I have the...
  15. Think of a bec like a car audio amp. It gives...

    Think of a bec like a car audio amp. It gives the servos and Rx a constant supply of power at the voltage it is set to. The castle ESC has a bed but I have been told it isn't strong enough and...
  16. If the two servos are at the same spec and at the...

    If the two servos are at the same spec and at the voltage you mention then I couldn't imagine being much of a difference. It could be possible that the higher voltage servo might run better. I run...
  17. Replies
    48
    Views
    1,175

    I was informed that the hyper 7 diffs did work. ...

    I was informed that the hyper 7 diffs did work. I was going to purchase those this weekend so I would like an answer as well. I just purchased the hybrids so I had an eye on those hyper 7's. I...
  18. Replies
    48
    Views
    1,175

    Hey what bearing size is used for those hybrid...

    Hey what bearing size is used for those hybrid bulks? And I have the lungsford pins and its my understanding that the bottom pin is different in size so I won't be able to use my Ti ones??
  19. Replies
    9
    Views
    253

    3908 brushless tranny

    3908 brushless tranny
  20. Replies
    48
    Views
    1,175

    Ya I def will! But I have done my research and I...

    Ya I def will! But I have done my research and I read so much on the flm's and 1/8 th diff completing the drive line issues. I will try to get my hands on some next weekend so I'm stoked!!

    But...
  21. I'm sure would work, feels like to me its more...

    I'm sure would work, feels like to me its more balanced having motor in the center and battery on either side of the chassis. But if the two batteries and motor weigh the same together then I would...
  22. Replies
    9
    Views
    253

    The top one is metal or steel, middle is plastic...

    The top one is metal or steel, middle is plastic and bottom is metel or steel. I bought an aluminum one on clearance, and wonder if it would be a good replacement for the plastic gear??
  23. Only thing with the flm mount is it mounts the...

    Only thing with the flm mount is it mounts the motor on one side of the chassis, the right side and not making enough room for a second battery if required too.
  24. The castle 10 amp bec. Its in the traxxas...

    The castle 10 amp bec. Its in the traxxas stampede Rx box right underneath the motor. Fixs perfect.
    ...
  25. Replies
    9
    Views
    253

    I have bought the alternative traxxas gear that...

    I have bought the alternative traxxas gear that is aluminum to replace the plastic one y'all are referring too. I bought it on clearance and was wondering would it be a good idea to change it or...
Results 1 to 25 of 65
Page 1 of 3 1 2 3