Search:

Type: Posts; User: J-DUB

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. If you keep it on low punch you will extend your...

    If you keep it on low punch you will extend your time till you need steel CVD's but you will notice your truck will run smoother with the new shafts. I have been running mine HARD (standing backflips...
  2. Very nice. Do you have steel center cvds? If not...

    Very nice. Do you have steel center cvds? If not you will have to be easy on the maxx till you do. Then eventually when you push it harder you will have to get the steel outdrives. Other then that...
  3. Replies
    25
    Views
    749

    IF you run 3s make sure it has about 7000mah and...

    IF you run 3s make sure it has about 7000mah and a 50c rating to make sure it can supply enough amps and not blow up on you.
  4. Replies
    25
    Views
    749

    That would be a great combo. Pair that with some...

    That would be a great combo. Pair that with some good lipos and you will be ripping it up for a long time.
  5. Replies
    5
    Views
    694

    http://www.*********.com/*********/store/__18611__...

    http://www.*********.com/*********/store/__18611__*****_*********_5900mah_2S2P_60C_Hardcase_Car_Lipoly.html

    These packs look very good I use some *****s in my slash 4x4 great punch till it hits...
  6. Replies
    5
    Views
    694

    They will hold up well if you break them in for a...

    They will hold up well if you break them in for a few runs BELOW 50% throttle. Also dont do reverse to forward wheelies! If you are going to run in taller grass then a would put 2-3t smaller pinions...
  7. Thread: Going Bodiless

    by J-DUB
    Replies
    6
    Views
    531

    http://www.rcraveninc.com/product/EMFRCBLACK3908/E...

    http://www.rcraveninc.com/product/EMFRCBLACK3908/E-Maxx-3908-3903-Black-Polished-Stainless-Steel-Full-Roll-Cage.html

    Look at this cage it looks like it would handle the abuse well.
  8. Replies
    25
    Views
    749

    Im sorry (was doing 3 things at once) I ment to...

    Im sorry (was doing 3 things at once) I ment to say the battery but 2s is going to be super slow but it is a good idea to get used to the power. I would for sure gear it lower to help with the strain.
  9. Replies
    25
    Views
    749

    Depends on what mah you get. 5000mah is usually...

    Depends on what mah you get. 5000mah is usually around 15-20 with an average use of 60-70% throttle. Also depends on where you run it too like tall grass or dirt or pavement. I have 8000mah and I can...
  10. Thread: e maxx 775

    by J-DUB
    Replies
    4
    Views
    311

    The 775 is a great motor but it can heat up fast....

    The 775 is a great motor but it can heat up fast. I would get the dual 700 combo just cause it will be easier on the motors cause their are two motors instead of one. Also if you break the motor...
  11. Replies
    25
    Views
    749

    The ezruns are a good system I had mine for a...

    The ezruns are a good system I had mine for a while till it gave up the magic smoke. It would pull wheelies at any point also invest in a good set of lipos so you can supply more than you will need...
  12. Replies
    18
    Views
    1,097

    Very nice should work really well!

    Very nice should work really well!
  13. Replies
    9
    Views
    695

    Unless you are crawling or mud running I would...

    Unless you are crawling or mud running I would think that fluid filled diffs would be better but like said above it will be your best option if you want more true 4wd.
  14. Replies
    14
    Views
    668

    Heatsinks for the stock motors now and CVD's...

    Heatsinks for the stock motors now and CVD's cause when you go BL you WILL need them!
  15. Replies
    18
    Views
    1,097

    It say right on the site for the parts "Fast...

    It say right on the site for the parts "Fast Lane's extreme abuse warranty.".
  16. Replies
    125
    Views
    4,265

    Make sure when you set the mesh that you can rock...

    Make sure when you set the mesh that you can rock the spur back and forth a little bit and the teeth on the spur and pinions hit in the middle of each other.
  17. Replies
    31
    Views
    1,539

    I would bite the bullet and get the aluminum...

    I would bite the bullet and get the aluminum bulks and towers cause in the end they will last much longer than the plastic. I have aluminum bulks and towers and they have not bent or anything and I...
  18. Yeah I had one but it gave up the magic smoke it...

    Yeah I had one but it gave up the magic smoke it was great when I had it but I know CC is a little easier to deal with that is the main reason why I went with the MMM.
  19. Looks alright but I think I will stay with the...

    Looks alright but I think I will stay with the tride and true MMM 2200Kv setup.
  20. Thread: Going Bodiless

    by J-DUB
    Replies
    6
    Views
    531

    Yeah I am just not sure with they way that it...

    Yeah I am just not sure with they way that it mounts to the bulkheads cause it looks like a good roll over and they would bend on the integy cage.
  21. Thread: Single 4s lipo

    by J-DUB
    Replies
    4
    Views
    309

    I think you could but you would have to make a...

    I think you could but you would have to make a reverse series harness to connect it.
  22. Replies
    18
    Views
    1,097

    OH Really?!?! They do have a warranty for them. I...

    OH Really?!?! They do have a warranty for them. I would call them cause I would think that it would be pretty hard to bend those. Could I see a pic of them?
  23. Replies
    18
    Views
    1,097

    If you want the best bulk and tower combo FLM is...

    If you want the best bulk and tower combo FLM is the only way! I have had mine for almost 4 years now and god knows how many flips and roll overs and upsidedown skids they have been through they are...
  24. Replies
    2
    Views
    674

    Probably just a bad piece out of the bunch Ive...

    Probably just a bad piece out of the bunch Ive had mine on for 3 years and no problems and also if it slips too much it could have gotten too hot. I would get the slipper pads that come in the 3908...
  25. Thread: Going Bodiless

    by J-DUB
    Replies
    6
    Views
    531

    I would say that is better if you are going for a...

    I would say that is better if you are going for a scale look of some sort but if you want a good cage (and the money) look into a rc solutions roll cage. I built one about 3 years ago and its still...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4