Search:

Type: Posts; User: Kawi

Page 1 of 6 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    15
    Views
    386

    No i never did, I just tightened them up enough...

    No i never did, I just tightened them up enough to keep them on.
  2. Replies
    3
    Views
    116

    Hmm, i did recently replace the gears. And it...

    Hmm, i did recently replace the gears. And it would affect the throttle while running though?
  3. Replies
    3
    Views
    116

    problem after new esc

    I installed the sidewinder 3 on my e-revo after the stock one kept going to overheat mode with no overheating. I did the whole thing perfectly (as far as I could tell), I ran it on a 2s not fully...
  4. Took out the 2nd channel plug for a sec and now motor won't turn

    Long story short I needed to see something involving another car, so I opened the receiver on the e-revo and pulled out Ch2 wire, i immediately put it back in and then noticed the light on the esc...
  5. Replies
    6
    Views
    239

    Well, I officially don't have an esc problem. It...

    Well, I officially don't have an esc problem. It was the battery I am sure. Tonight I said screw this. I slapped on a 2s 5800 mah on the roof, inside a cloth glove . I just spent the last 45 minutes...
  6. Replies
    6
    Views
    239

    thanks for the replies. I'm actually a bit...

    thanks for the replies. I'm actually a bit confused now. It looks like it might not be the esc. I think it might be a bad battery. Brand new 2s 2200. It only cuts out to a crawl on this one battery I...
  7. Replies
    6
    Views
    239

    Thank you peterje60, I was starting to think I'd...

    Thank you peterje60, I was starting to think I'd asked a bizarre question! I checked it out, my lhs has them in stock, the sv3, 78 bucks, and it's waterproof. Why couldn't I find this answer anywhere...
  8. Replies
    6
    Views
    239

    Are there any upgrades available for esc?

    My esc has just about pooped the bed. By the time I hit about 3.8v on the 2s it's slowing down to a crawl, then picks up again, then crawl. I made another thread about that anyway. So my question is,...
  9. Replies
    4
    Views
    157

    I have a 45T one. Is that better? Will it be...

    I have a 45T one. Is that better? Will it be quicker or higher top speed?

    Is this a sign of overheating esc? Does the esc act this way?
  10. Replies
    4
    Views
    157

    e-revo suddenly losing power

    I just finished installing a new gear and pinion in the rear, the last one was clicking, so I added 2 more shims for a total of 4. I ran it about 3 batteries and it did fine, on gravel, and just now...
  11. Replies
    15
    Views
    386

    I'll do that next time I take it apart for sure....

    I'll do that next time I take it apart for sure. Went to the hardware store and got some #6x32 nuts and some self locking ones as well, just to use on that one wheel until i get to the lhs. The self...
  12. Replies
    15
    Views
    386

    No I have new driveshafts. I also just put new...

    No I have new driveshafts. I also just put new diff gears front and back and shimmed. Regarding the "crush tube", never heard of that. In between bearings how? You mean on the inside if the big...
  13. Replies
    15
    Views
    386

    They look like they did when they were new. I...

    They look like they did when they were new. I think it's the new hubs, I just installed new cvd's, and they probably don't seat perfectly onto the bearings. I don't know what else it could be. I was...
  14. Replies
    15
    Views
    386

    Axle carriers is what I meant. Like I said...

    Axle carriers is what I meant. Like I said though, on the rpm axle carriers, it doesn't tightn up, just on the front aluminum ones. Very strange. I'm outa commision anyway now that I lost a wheel...
  15. Replies
    15
    Views
    386

    I did, that's the first thing I tried actually,...

    I did, that's the first thing I tried actually, it didn't make a difference.Still stiffens right up as I tighten. It seems that the more you tighten the wheel, the more you pull the entire hub in...
  16. Replies
    15
    Views
    386

    Wheels are too tight

    I just bought some new wheels for the revo, package says "Dirt Hawg off road tires mounted on titus bead-loc wheels". Each wheel came with a little black washer. I mounted the wheels and put the...
  17. Replies
    57
    Views
    2,367

    Ill check again but I couldn't duplicate any...

    Ill check again but I couldn't duplicate any binding when i looked for it. it may have to do with the tires. I know one is very soft for some reason, you can squeeze it with no pressure, like a very...
  18. The 2 casings from ebay

    The 2 casings from ebay
  19. Wow, as of I could have just done that! Exactly...

    Wow, as of I could have just done that! Exactly what is the deal with that anyway, where do those come from? Traxxas, or aftermarket? I can't see the details from my phone.
  20. Replies
    57
    Views
    2,367

    So wow, big thumbs up to Traxxas who came through...

    So wow, big thumbs up to Traxxas who came through for me in the end with a new motor which is on its way, and an even bigger thumbs up to ksb51rl who took the time to intervene into my unique...
  21. Looks like I'm stuck anyway. The left...

    Looks like I'm stuck anyway. The left driveshaft's hex screw is beyond stripped, the axle cant come off which it needs to do to allow me to shim that side of the gear. If I shim the other side it...
  22. I see some dullness for sure but it's just I...

    I see some dullness for sure but it's just I found it odd that I would get such stripping from that, I'm used to other gears in helis for examlpe that are plastic and don't stop meshing until they're...
  23. Replies
    14
    Views
    769

    I don't have a readout. It's a cuircit board...

    I don't have a readout. It's a cuircit board with a speaker that plugs into the battery port. I have to check it after I get it out.
  24. Replies
    14
    Views
    769

    I never set mine, not sure how, but when they go...

    I never set mine, not sure how, but when they go off I check them and they're around 3.4. I've had no issues.
  25. So I got the new gears, got them installed and...

    So I got the new gears, got them installed and I'm about to close the casing up. What is this "shimming" that I should do?

    BTW these are the gears side by side. I can't really see much wear.
    ...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4