Search:

Type: Posts; User: kpalmer65

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    75
    Views
    3,282

    These trucks are a blast! My boys and I have had...

    These trucks are a blast! My boys and I have had a lot of fun bashing and working on them. I had found some videos that I found quite helpful. I saved a playlist list of a complete build of one...
  2. Replies
    8
    Views
    473

    Yeah, I was planning on doing the shoe-goo and...

    Yeah, I was planning on doing the shoe-goo and tape. We did that to repair the stock body, but was too late for the bed holes. It really would have helped to do it before any cracking started.
  3. Replies
    8
    Views
    473

    Digger, Pictures of yours is what set him up...

    Digger,

    Pictures of yours is what set him up with wanting one! What are your opinions of its durability? My son is 10 and spends what seems like 75% of the time on the lid. Not that I am much...
  4. Replies
    6
    Views
    315

    Here are the bearings...

    Here are the bearings to replace the bushings. When my son replaced the bushings on his truck, it was unbelievable how much quicker the truck ran! The bearings already come in the VXL version and...
  5. Replies
    8
    Views
    473

    Best way to mount Gate Crasher Body

    My son finally destroyed the stock body on his pede. He really likes the look of the Gate Crasher body. This is the first time I have had to put a new body on our three trucks. What is the best...
  6. Replies
    22
    Views
    606

    I used this method ...

    I used this method to lower my body with two sets of rustler battery post kit PN TRA3727. Pretty simple, just $6 in parts.
  7. Replies
    10
    Views
    470

    I was playing with this the other day. Is there...

    I was playing with this the other day. Is there an easier way to adjusting the slipper without removing the whole back half everytime?
  8. Replies
    12
    Views
    263

    I just love seeing the smiles on the kids when...

    I just love seeing the smiles on the kids when they are so excited about something. So far with both my boys, if they have the controller in hand running their truck, nothing but big smiles!! Lots...
  9. Replies
    4
    Views
    528

    Thanks! I will go out and read the label on my...

    Thanks! I will go out and read the label on my bearing grease in the shop.
  10. Replies
    4
    Views
    528

    MIP CVD Assembly

    Well, after my first 2 runs of changing to lipo I destroyed 2 sets of plastic CVDs. Good thing I was anticipating this and asked for MIP CVDs for Christmas!

    I assembled them last night using red...
  11. Replies
    12
    Views
    323

    Third Stampede showed up today! UPDATE: Maiden Voyage

    We spent some time yesterday getting the truck set up.

    First he had to install some shocks on the pede. I upgraded to Big Bores on my 4X4, so I gave him my ultras. Then he removed the xl-5 esc...
  12. Replies
    0
    Views
    373

    Pavmentsurfer--Fantastic to work with!

    Thanks Pave for working with me to figure out what we needed and getting it to us!!

    Keith
  13. Replies
    12
    Views
    323

    Third Stampede showed up today!

    My youngest son was feeling left out when his brother and I were driving our stampedes and he was stuck driving the old RC10. He didn't like that he couldn't go in the grass and jumps like we could....
  14. Replies
    5
    Views
    135

    Thats wierd, because they show up when I look at...

    Thats wierd, because they show up when I look at the post.
  15. Replies
    5
    Views
    135

    Finally tried our new Lipos

    We finally got a chance to charge up the new SPC lipos I bought for Christmas and take the trucks out this weekend. Unfortunately I broke my rear axles on my 4x4 5 minutes into my run. Now, I just...
  16. Replies
    6
    Views
    363

    Thanks Loot!!

    Thanks Loot!!
  17. Replies
    6
    Views
    363

    FlySky GT3B rx antenna?

    I got my son this 2.4 system for his stampede for Christmas. We were just installing it, but the antenna is so short. Only about 2" of the wire goes up into the tube if you use the stock location....
  18. Replies
    10
    Views
    315

    Well, we got some time tonight to do the swap! I...

    Well, we got some time tonight to do the swap! I really enjoyed supervising while he did the work. Once we got it together, he did take a little spin on the back porch in the dark. We found...
  19. Replies
    0
    Views
    383

    Paulfromtulsa Great Seller

    Great seller! Would buy from him again. He was very patient working with my question. Parts were well packed.

    Keith
  20. Replies
    10
    Views
    315

    Thanks guys! The boys have swimming lessons...

    Thanks guys! The boys have swimming lessons tonight, so we will get to it tomorrow. Will keep you posted of the progress!
  21. Replies
    8
    Views
    807

    Sorry, accidentally replied to wrong thread. ...

    Sorry, accidentally replied to wrong thread. Please delete.
  22. Replies
    10
    Views
    315

    A couple more questions. I was wondering if we...

    A couple more questions.

    I was wondering if we needed to change the gearing? We have 17/90 in it now. He drives it mostly in the backyard on the grass and the gravel driveway.

    I am planning...
  23. Replies
    10
    Views
    315

    OK thanks! He already put bearings in, they made...

    OK thanks! He already put bearings in, they made a huge difference in speed! This is his truck and he is paying for the upgrades, so we are upgrading as things break. It sure has given him some...
  24. Replies
    10
    Views
    315

    Brushed to Brushless How to?

    My son just picked up a Velineon VXL 3s esc and 3500 motor to upgrade his brushed truck. Do we need to do anything other than swap out the parts to get it running on the brushless setup?

    Thanks...
  25. Replies
    5
    Views
    335

    PM has been sent

    PM has been sent
Results 1 to 25 of 38
Page 1 of 2 1 2