Search:

Type: Posts; User: Jclay

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    14
    Views
    2,433

    Those are 0.8 pitch clutch bells for the Jato...

    Those are 0.8 pitch clutch bells for the Jato that are shown above. The ones that is hard to find is 1.0 pitch which is the same pitch that the Revo uses. Since there is no 36T 0.8 pitch spur gear...
  2. Replies
    14
    Views
    2,433

    Sorry for the wait. The 36T Spur gear is a Revo...

    Sorry for the wait. The 36T Spur gear is a Revo 36T. The Clutchbell will be harder to find. It is made by Ofna and it a two piece screw-on clutchbell.
  3. Replies
    14
    Views
    2,433

    All steel transmission 36/24 gearing Novarossi...

    All steel transmission
    36/24 gearing
    Novarossi base Engine (Big Block)
    Extended Chassis
    40% Nitro Fuel
    Modified springs to go low as possible
    Conical Manifold to increase rpms
    EFRA Pipe
    I...
  4. Thread: spur gear ?

    by Jclay
    Replies
    14
    Views
    1,059

    Sounds like it needs more torque. What type of...

    Sounds like it needs more torque. What type of packs you are running? Your motor provide 99 percent of your torque the rest is gearing. You shouldn't have to go that high in order to wheelie.
  5. Replies
    19
    Views
    3,139

    You would have to do some modding because the...

    You would have to do some modding because the mounting holes are different on a Big Block chassis.
  6. Replies
    6
    Views
    1,844

    Most engines hold its tune in at the LSN meaning...

    Most engines hold its tune in at the LSN meaning once set you shouldn't have to mess with it unless you changing fuel with a different Nitro percentage. It’s usually the HSN that you need to change...
  7. Replies
    26
    Views
    5,494

    Sí sé que puede ser difícil de conseguir las...

    Sí sé que puede ser difícil de conseguir las piezas a otros países como Chile. Hay algunos lugares como amainhobbies.com que hacen envíos internacionales les daría una oportunidad.
    Ah, sí sintonía...
  8. :lol: Out of all the years into R/C I never...

    :lol: Out of all the years into R/C I never heard of RedCat.
  9. Maybe you should think about upgrading your...

    Maybe you should think about upgrading your batteries and charger. I see Rustlers get up to 35min of run time on a 5000mah lipo min which is actually 3 times longer than you would get from the Jato....
  10. Replies
    51
    Views
    4,535

    You will need a blackplate, and a one-way...

    You will need a blackplate, and a one-way bearing. I am not sure if the stock traxxas OWB will work or not. Also you can use the drill but you will need to change the shaft because it uses a larger...
  11. Replies
    4
    Views
    772

    Jato weighs 83oz stock. Your typical 6 cell NimH...

    Jato weighs 83oz stock. Your typical 6 cell NimH 7.2v 5000mah weighs 16oz so a combine weight of 99oz. 16 percent of the weight is the battery alone. Your typical 2S 7.4v 5000mah Lipo weighs 8.1 oz...
  12. Replies
    4
    Views
    772

    Well exercise is always a good method to lose...

    Well exercise is always a good method to lose weight.. Ok all jokes aside Jato is a light truck to begin with. Unless you gonna by the carbon fiber chassis there not going to be much difference in...
  13. Thread: Tallest Gearing

    by Jclay
    Replies
    11
    Views
    1,118

    The OS .21 has more torque than the 3.3 there is...

    The OS .21 has more torque than the 3.3 there is no question about that. When I had the OS .21 with 20/40 gearing I would top out just less than 60mph with the GPS attached. Manufactures always...
  14. Thread: Tallest Gearing

    by Jclay
    Replies
    11
    Views
    1,118

    Yes you are correct you have to saw off the first...

    Yes you are correct you have to saw off the first speed gear. The TRX 3.3 gives you more speed than the OS.21 It just doesn't have the rpm range needed to even get up to +65mph.
  15. Replies
    12
    Views
    1,983

    That EZ wiring harness isn't the best. What I...

    That EZ wiring harness isn't the best. What I did was just cut the wire that ignites the glow plug. Get yourself a standard glow plug igniter. Usually cost about $15- 20 at your LHS. It works a lot...
  16. Replies
    1
    Views
    789

    I had many of MIP clutch shoes and those are the...

    I had many of MIP clutch shoes and those are the hardest to assemble in my opinion. The spring that comes with it is a headache. If you are using REVO gearing then use a Revo stock clutch shoes and...
  17. Replies
    19
    Views
    3,139

    Nothing like good ole stock clutch shoes.

    Nothing like good ole stock clutch shoes.
  18. Replies
    2
    Views
    833

    BSWIFT - 84mph with a TRX 3.3 and 93 with an Big...

    BSWIFT - 84mph with a TRX 3.3 and 93 with an Big Block


    http://www.youtube.com/watch?v=u4wDhcls7XQ&feature=player_profilepage
  19. Replies
    6
    Views
    1,156

    Traxxas steel shafts are great, and gives you a...

    Traxxas steel shafts are great, and gives you a tad bit of increase acceleration due to the less rotating mass.
  20. Replies
    12
    Views
    4,923

    Whats make you so sure they will come out with a...

    Whats make you so sure they will come out with a gas power RC?
  21. Replies
    59
    Views
    5,352

    With all these classics cars you guys are naming...

    With all these classics cars you guys are naming you should have come out to our Annual Dream Cruise which was today.
  22. Replies
    12
    Views
    4,923

    1/5 scale from Traxxas?

    Is there any faith in Traxxas that they will make a 1/5 scale R/C truck/car? The last one was years ago called the Monster buggy. Since now there are brushless systems available for 1/5 I would love...
  23. Thread: Tallest Gearing

    by Jclay
    Replies
    11
    Views
    1,118

    PM sent....

    PM sent....
  24. Thread: high idle

    by Jclay
    Replies
    5
    Views
    1,139

    Usually its the return spring doesn't have enough...

    Usually its the return spring doesn't have enough tension. Tighten the tension and it should solve that problem.
  25. Thread: Tallest Gearing

    by Jclay
    Replies
    11
    Views
    1,118

    24/34 is the tallest However, there is a 26T...

    24/34 is the tallest However, there is a 26T clutchbell that you will have to slightly modify in over to fit it on the Jato.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4