Search:

Type: Posts; User: KartRacer45

Page 1 of 9 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    5
    Views
    669

    Thanks, I may try the E-Bay route!!

    Thanks, I may try the E-Bay route!!
  2. Replies
    5
    Views
    669

    Still available. Will have more pics soon. Make...

    Still available. Will have more pics soon. Make offer.
  3. Replies
    5
    Views
    669

    $450 Or Best Offer

    $450 Or Best Offer
  4. Replies
    5
    Views
    669

    Price reduced $500 or best offer.

    Price reduced $500 or best offer.
  5. Replies
    5
    Views
    669

    Not willing to separate at this time.

    Not willing to separate at this time.
  6. Replies
    5
    Views
    669

    Complete Sellout

    Got into nitro about 6 years ago, went into it big time!! Shortly after me and my wife had our first child so I lost all interest. Now its time to get it out of the garage, has not been out the the...
  7. Replies
    1
    Views
    194

    Complete sellout

    Please delete.
  8. Replies
    6
    Views
    580

    I use my Ofna Roto Start With a Ofna Backplate...

    I use my Ofna Roto Start With a Ofna Backplate that 100% DOES use the stock Traxxas OWB!!!!!!!!!

    I got both from A-Main
  9. Replies
    11
    Views
    369

    You can buy just the bearings are re-install them.

    You can buy just the bearings are re-install them.
  10. Replies
    17
    Views
    430

    I now run the Maximizer Aluminum Hexes, ZERO slop...

    I now run the Maximizer Aluminum Hexes, ZERO slop at all. This will be the ONLY adapter I ever buy again!!
  11. Replies
    79
    Views
    2,433

    Oomp, You are 100% accurate!!! MC-59 will...

    Oomp,

    You are 100% accurate!!!

    MC-59 will work fine in a Traxxas engines, The two I measured were in fact a little shorter than the Traxxas plugs, about .003 each.:)

    I do feel that the...
  12. Replies
    17
    Views
    444

    Yeah what mods are needed for a TZ to install in...

    Yeah what mods are needed for a TZ to install in a revo.
  13. Replies
    79
    Views
    2,433

    I remember reading about the Modifications you...

    I remember reading about the Modifications you must make to install the TZ into a revo, but now I cannot find them. What must be done to install a .18 tz into a revo? I use a roto start.
  14. Replies
    24
    Views
    1,209

    I Have had very good luck with my Picco, At least...

    I Have had very good luck with my Picco, At least so far!! This is what "I" run.

    17/38 Gearing, Seems to give the best balance of low and top end.

    I run a McCoy MC-59 or a MC-8
  15. Replies
    14
    Views
    638

    Sleeve resizer

    Where can I purchase a sleeve resizer/pincher for a 2.5r and a 3.3?
  16. Replies
    0
    Views
    145

    Servo Question

    I encountered a strange problem with my BRAND SPANKIN NEW Throttle Servo. It's a Hitec HS-625mg, Worked fine for the fist day, then it all of a sudden would go Past its end point which held the...
  17. Replies
    68
    Views
    979

    Yeah thats what I was getting at. If you have...

    Yeah thats what I was getting at.

    If you have fuel and fire,,,, The Engine MUST aleast hit!!!

    You either do not have fuel getting to the combustion chamber or the glowplug is bad.
  18. Replies
    68
    Views
    979

    Are you CERTAIN the glowplug is getting hot? I...

    Are you CERTAIN the glowplug is getting hot?

    I would put a Glowplug in a glowplug igniter to MAKE SURE (By actually seeing the coil turn red) it is getting hot.

    If it is:::::

    Next I would...
  19. Replies
    68
    Views
    979

    Does it ever "hit" or attempt to run? If the...

    Does it ever "hit" or attempt to run?

    If the engine is getting fuel and Fire it will at least "hit"
  20. Replies
    76
    Views
    1,695

    I am afraid that YOU are the one misleading the...

    I am afraid that YOU are the one misleading the users. I am a mechanical engineer and if you are actually seeing this type of failure, It is Due to VERY poorly machined parts ALONG with a low quality...
  21. Replies
    76
    Views
    1,695

    Who has the RD Carriers in stock, I can't seem to...

    Who has the RD Carriers in stock, I can't seem to find them???? Nedd to order a set FAST!!!!!!
  22. Replies
    22
    Views
    694

    One thing to remember however, It is a lot easier...

    One thing to remember however, It is a lot easier to get good results with a GOOD quality Gun than it is an inferior one. A good quality gun will make the process A LOT easier and more enjoyable.
  23. Replies
    32
    Views
    1,263

    His Picco seems to be just fine!! I would say he...

    His Picco seems to be just fine!! I would say he is pushing the One gallon marks and so far so good. I had a pretty good temp derease AFTER the cryo treatment. I Run with temps in the 250 range,...
  24. Replies
    32
    Views
    1,263

    I'll agree with those 2 cents!!! It has really...

    I'll agree with those 2 cents!!! It has really helped with some wear issues on our Kart Engines, Hope it will do the same for these little suckers!!;)
  25. Replies
    42
    Views
    1,173

    This is NOT a correct statement, the Glow Plug...

    This is NOT a correct statement, the Glow Plug has a DIRECT effect on the "fire" of the engines cycle!!! Thus changing the timing of the engine.
Results 1 to 25 of 221
Page 1 of 9 1 2 3 4