Search:

Type: Posts; User: tymmo98

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    187

    Well, it's really strange because when the engine...

    Well, it's really strange because when the engine is not running, it shifts all the way and looking good

    Sent from my Galaxy S3 with Tapatalk
  2. Replies
    3
    Views
    187

    It was always good set, the servo is pulling to...

    It was always good set, the servo is pulling to the maximum. If I try to make it pull farer, it will push against the protection box. I will try to bend the linkage or whatever it is called.

    Sent...
  3. Replies
    3
    Views
    187

    Reverse problem

    Hello,
    When I try to shift into reverse, the servo works, it pulls good, put the little piece of metal which is in the transmission and is normally pulled all the way out gets stuck halfway. I can...
  4. Replies
    3
    Views
    271

    A few spaces away from the crank case on the...

    A few spaces away from the crank case on the cooling head

    Sent from my Galaxy S3 with Tapatalk
  5. Thread: High idle

    by tymmo98
    Replies
    4
    Views
    270

    Did you put the high speed needle, low speed...

    Did you put the high speed needle, low speed needle, and the idle screw at stock settings? If yes, clean and re-oil the air filter. Check the fuel tank, there is a metal "filter" which filters fuel...
  6. Thread: Loosing power

    by tymmo98
    Replies
    4
    Views
    234

    It is probably the spur gear unscrewing a bit....

    It is probably the spur gear unscrewing a bit. After you let it cool down, is it going good again? Probably not the diff oil. You maybe have a leak in the engine. Check for loose screws everywhere....
  7. Replies
    7
    Views
    328

    Just blow in the tube which connects the tank to...

    Just blow in the tube which connects the tank to the exhaust. Easier but stop blowing when it is in the carburetor, otherwise, you'll have to clear your engine.

    Envoyé depuis mon GT-I9300 avec...
  8. Replies
    13
    Views
    1,027

    Thank you guys for this advice. So let's do this!...

    Thank you guys for this advice. So let's do this! Installing it tomorrow. And the connectors on the battery box got pushed in.

    Envoyé depuis mon GT-I9300 avec Tapatalk
  9. Replies
    7
    Views
    329

    Take a glow ignitor so your EZ Start Battery will...

    Take a glow ignitor so your EZ Start Battery will last longer. And that is also 1 less cable :)

    Envoyé depuis mon GT-I9300 avec Tapatalk
  10. Replies
    15
    Views
    282

    Nice, I hope for you it's not going to get too...

    Nice, I hope for you it's not going to get too heavy. The must have aluminum parts are bulkheads, chassis (obvious), spur gear, driveshaft ends and the body mounts ( I mean the whole body mount part,...
  11. Replies
    13
    Views
    1,027

    EZ Start or Pull Start ?

    Hi,
    just asking : Which one is better ? Because when the Ez Start works, it is quite good but when the battery dies that's a pain.
    I asked to my hobby shop about replacing the Ez by a pull start...
  12. Replies
    33
    Views
    1,883

    The bulkheads, the spur gear, the left servo...

    The bulkheads, the spur gear, the left servo teeth, and the chassis is bent. Well, I find the chassis WAAAYYY to thin. My cyborg RAT 7 has the same thickness.
  13. Replies
    7
    Views
    328

    Thanks guys for your help !!! :)

    Thanks guys for your help !!! :)
  14. Replies
    7
    Views
    328

    Is this normal ?

    When I run my ( Brand new ) Revo, and after 10 minutes, when the tank is nearly empty, I open it, and vapour is coming out of it. Is this normal ?
  15. Replies
    2
    Views
    1,233

    Thank you.

    Thank you.
  16. Replies
    2
    Views
    1,233

    Speed difference but same engine ?

    Hi,
    There is something that I find really strange...
    I have the Revo 3.3 #5309, and I wanted to know why the speed is affected, per example, between a revo and a nitro 4 tec or a jato but it is...
  17. Replies
    2
    Views
    1,655

    Ok thank you

    Ok thank you
  18. Replies
    2
    Views
    436

    Ok thank you

    Ok thank you
  19. Replies
    2
    Views
    1,655

    TRX 3.3 Pull Start

    Hi guys, I was just wondering : Can we temporarily install a pull start on the 3.3 if the EZ Start battery is
    discharged ?
    Thank you for all future answers.
  20. Replies
    4
    Views
    1,640

    The best thing to do is idling in the garage but...

    The best thing to do is idling in the garage but not breaking in while it's raining. Actually never make it run when it's raining.
    The electronic case is not waterproof as well as the transmission...
  21. Replies
    1
    Views
    1,266

    Do you have it for a long time ? If yes, wait the...

    Do you have it for a long time ? If yes, wait the engine to warm up a bit by doing some full speed runs on a straight road.
    If it is new : It happened with me and my TRX 3.3, it was good after...
  22. Replies
    2
    Views
    436

    Ez Start Battery Compatibility

    Hi to all,
    I don't know if a thread like this already exists ( Yes, I've searched ) but I was just wondering : Can we
    change the battery on the EZ Start with a more powerful voltage or MAH ? ( I...
Results 1 to 22 of 23