Search:

Type: Posts; User: DK slayer

Page 1 of 3 1 2 3

Search: Search took 0.18 seconds.

  1. Replies
    0
    Views
    137

    Beast of a slayer

    Here is a steal of a deal to someone out there who wants a bad to the bone slayer. It is a Traxxas slayer pro that has been converted to a big block with all kinds of top of the line and custom...
  2. Replies
    33
    Views
    416

    Well it just happens and obviously you are more...

    Well it just happens and obviously you are more of the lucky few than the rest of us.
  3. Replies
    33
    Views
    416

    I have done all of this. The set screw does not...

    I have done all of this. The set screw does not seem to have backed off. Most of the time the pinion is still pretty snug but I can slide it around if I try.
  4. Replies
    33
    Views
    416

    Pinion keeps moving.

    After a run I always blow the truck off with compressed air and then bring it inside and just check it over. One thing I also do is remove the cover for the pinion and spur gear and check mesh and...
  5. I have the lcg chassis and I noticed a small...

    I have the lcg chassis and I noticed a small amount of that very same play once the unit was installed. To be fair the stock unit had the same amount and I would say that it is about 1/3 as much as...
  6. Installed the Robinson unit today and went out on...

    Installed the Robinson unit today and went out on a fresh 6s pack. I still had to tighten the nut for the slipper all the way down but it holds the power as far as I can tell. I can nail it from a...
  7. I bought the robinson racing gen 3 unit earlier...

    I bought the robinson racing gen 3 unit earlier today. This will make the entire driveline upgraded.
  8. I took my slash out today for the second time on...

    I took my slash out today for the second time on a full 6s pack and the stock slipper just will not hold this motor under hardly any condition. I didn't think I was going to have to upgrade it so...
  9. Those clutches look real nice. I am going to have...

    Those clutches look real nice. I am going to have to upgrade mine soon.
  10. To me if you are just bashing and racing I would...

    To me if you are just bashing and racing I would go 4s. Since you are looking for speed I would have went straight for 6s.
  11. Ahh, Gotcha. If it is more speed that you are...

    Ahh, Gotcha. If it is more speed that you are after and you are already running a 22/54 setup then you need to bump your cell count up and get ready for triple digit speed.
  12. I would pick up 18,20, and 22t pinions to have...

    I would pick up 18,20, and 22t pinions to have some options. I would just leave the spur at 54t as you can adjust the pinion easily to whatever you need to do. If you are looking for a cheap option...
  13. Replies
    38
    Views
    878

    Who makes a great 6s pack?

    Who makes a great 6s pack?
  14. Thread: Diff I Beam

    by DK slayer
    Replies
    12
    Views
    276

    Its $17, buy the thing....

    Its $17, buy the thing....
  15. Ran it for the first time tonite. The battery...

    Ran it for the first time tonite. The battery strap is super solid btw. Before it is even strapped down it fits the battery compartment very snugly. All the strap has to do it hold it down and it's...
  16. Replies
    21
    Views
    654

    That thing is moving.... whats it like with a...

    That thing is moving.... whats it like with a body on it?
  17. What is the tallest battery you can fit under...

    What is the tallest battery you can fit under that? That is a 6s pack and its around 49mm tall.
  18. Update, got the xo-1 esc mount today and it mates...

    Update, got the xo-1 esc mount today and it mates right up to a pair of existing holes in the chassis. One thing you can't say about my builds is that they are not clean.
    ...
  19. It's getting there.... ...

    It's getting there....

    http://img.tapatalk.com/d/14/02/24/3u9utuhe.jpg
  20. Replies
    8
    Views
    263

    I like to run 17mm conversion because I can run...

    I like to run 17mm conversion because I can run any 1/8 wheel tire combo. Most come in around 4.5" total diamater which is just about .2" larger than the stock size. The extra diamater can be...
  21. Ok I bought some M3x8 countersunk screws among...

    Ok I bought some M3x8 countersunk screws among other things today. I took the plate off of the front of the motor and the total thickness of where the threaded portion is for the screws to engage and...
  22. Those with mamba monster help me out here.

    When I bought my roller that was parted out from a 6807L it did not come with the counter sunk screws that mount the motor to the blue plate for the motor mount. I have found that the stock size is...
  23. Replies
    7
    Views
    291

    Yeah the servo on mine lays on its side and takes...

    Yeah the servo on mine lays on its side and takes up a bit of that room up there where the esc gets pushed into. I am sure I will figure it out when it is all here in front of me
  24. Replies
    7
    Views
    291

    Yeah I didn't even see that sub forum until it...

    Yeah I didn't even see that sub forum until it was too late. Plz move this
  25. Replies
    7
    Views
    291

    Also on 6s this thing will just be doing speed...

    Also on 6s this thing will just be doing speed runs. I will go lower cell count for bashing or racing. I am going to just crank down on the stock shocks for now. I really don't want to dump any more...
Results 1 to 25 of 53
Page 1 of 3 1 2 3