Search:

Type: Posts; User: Wheeler

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Replies
    340
    Views
    157,793

    Here is a link to my new body. It is a custom...

    Here is a link to my new body.

    It is a custom job. I bought some Mirage Paint from Advanced Auto Parts, and it looks sweet. I'm a little hesitant to take it out and bash with it...I will...
  2. Replies
    80
    Views
    74,851

    Sticky: Here is a link to my new body. It is a custom...

    Here is a link to my new body.

    It is a custom job with the "mirage" paint you can buy from a local car parts store. Paint changes colors in the light.
    ...
  3. Replies
    2
    Views
    233

    Changing Stinger Brushes

    Hey,

    How do you change the brushes out of the stock stinger motor? I have a bad noise coming from the motor, and I'm pretty sure one of the brushes is rubbing against the stator.

    I landed...
  4. Replies
    6
    Views
    277

    50/50 vs. 70/30?

    Hey,

    On my controller, there's a switch that allows me to select 50/50 or 70/30. I played with the switch a little bit, and I think I understand the basic premise, but when I swap between the two...
  5. Replies
    5
    Views
    277

    Awsome. Wish I were there with ya. :)

    Awsome. Wish I were there with ya. :)
  6. Replies
    9
    Views
    401

    Why does it say "Tower's Low Price" above the...

    Why does it say "Tower's Low Price" above the price if that isn't what they are going to charge?
  7. Replies
    7
    Views
    293

    I've dumped my 'pede more in the last three days...

    I've dumped my 'pede more in the last three days since I got my m2ks put on than I ever have before.

    One thing about it...It's teaching me throttle control. Poor body's all beat up :(
  8. Replies
    4
    Views
    195

    Yeah, I upgraded the bearings and carriers, and...

    Yeah, I upgraded the bearings and carriers, and the play was improved a lot, but when I spun the tires, I noticed the wheel itself wobbling too, not just the tire.

    The wheel is tight against the...
  9. Replies
    4
    Views
    195

    balancing the wheels/tires

    I glued my new masher 2ks to my new wheels last night (didn't make a mess either:) )

    When I lift the front end off the table, the wheels rotated on their own, obviously the tire/wheel is heavier...
  10. Replies
    26
    Views
    767

    I played with X-Mods for a loooong time, and when...

    I played with X-Mods for a loooong time, and when the new X-Mods came out, they were faster, and there were some chassis changes that made it unique from the old Chassis.

    The point is when the new...
  11. I don't know, but I thought 12 was a little low...

    I don't know, but I thought 12 was a little low for the pinion
  12. Replies
    3
    Views
    147

    Thanks guys.

    Thanks guys.
  13. Replies
    3
    Views
    147

    How to post pics

    Can anyone help me with this? I have some pics I would like to post:cool:
  14. Replies
    11
    Views
    247

    OK, so the servo saver stays plastic. I guess I...

    OK, so the servo saver stays plastic. I guess I envisioned the whole mechanical steering system as metal.

    I would be leary changing something so complex as steering to all metal. The plastic...
  15. Replies
    5
    Views
    210

    Start with the basics...I know it sounds like a...

    Start with the basics...I know it sounds like a waste of time, but I am an EE and I know how easy it is to overlook the simple stuff. Here we go.

    1. Check the battery. Is the battery fresh? ...
  16. Replies
    11
    Views
    247

    I think I would keep plastic. Better to replace...

    I think I would keep plastic. Better to replace a couple of dollars worth of gears because you hit something, than to replace knuckles, tie rods, wheels, and maybe even the electronics controlling...
  17. Replies
    10
    Views
    261

    Interestingly enough, after I did this last...

    Interestingly enough, after I did this last night, it seemed like it was only 1/8 to 1/4 turn I had to back off from completely tight.
  18. Replies
    10
    Views
    261

    M pede came with a suggestion on how to adjust...

    M pede came with a suggestion on how to adjust the clutch. It says to place the truck on a high traction surface, like carpet, then floor the accelerator. The truck should whine for about two feet...
  19. Replies
    12
    Views
    166

    Could it be that his clutch needs adjusting? ...

    Could it be that his clutch needs adjusting? Might need to tighten it up a bit, or take Brand's suggestion, "take it back".
  20. Thread: Driving Tips

    by Wheeler
    Replies
    17
    Views
    292

    Practice, break stuff... Practice some more,...

    Practice, break stuff...

    Practice some more, break more stuff...

    Practice even more, break even more stuff...
  21. Replies
    30
    Views
    479

    Uhmm...So do I leave the foam in the tires, or...

    Uhmm...So do I leave the foam in the tires, or toss them?
  22. Replies
    7
    Views
    204

    I can't tell you about the long term reliability...

    I can't tell you about the long term reliability because I just bought mine Saturday, but I can tell you that I get at least 20 mph out of the box, and it is the best toy I have ever bought (and I...
  23. Replies
    30
    Views
    479

    Here is a link to a picture of the wheels. They...

    Here is a link to a picture of the wheels. They are for HPI, but they have the adapter to fit the stampede in the package.

    http://www.hpiracing.com/piw4.php?part=3082
  24. Replies
    30
    Views
    479

    All of the wheels are the same depth. Normally,...

    All of the wheels are the same depth. Normally, the rear wheels would be shallow and the front wheels would be deep, and when they are installed, the rear end is just as wide as the front end, but...
  25. Replies
    30
    Views
    479

    I just got back, and this is what I got. Masher...

    I just got back, and this is what I got. Masher 2k tires, new rims, 5x11 bearings, and bearing carriers, and the bumper. I am going to wait on the motor and ESC for now.

    Do I have to glue the...
Results 1 to 25 of 32
Page 1 of 2 1 2