Forum: Slash 4X4

Since my Baja body has passed away. I figured a new thread would be needed to detail my track queens progressions, jk... still bash occasionally. She...

I posted this in the alley and got no response so here is the question. Will my stock tmaxx shocks fit on my slash 4x4(when i get one)? I was...

After hooking up my battery today I found the throttle did not work. Took a look at the ESC and found the light is not on, but the steering still...

Other then the motor and ESC what will I need to se this combo up? I will be getting the CC MMP and the Novak 5.5HV. I know the MMP has bullets...

I'm going to get a slash next week just wondering how durable the PE or the 4x4 rtr slashes in general. My friend has the 2wd slash and that holds up...

I was wondering, is the Castle Creations Mamba Sidewinder esc and motor cmbo good for this truck or is it just a waste of money to put in the 4x4? If...

This is a box stock 4x4 with the new body! Let me know what you guys think!!?? I love this Silverado body!!!

Parts need: - 4 metal ring for the shock ends - 4 baloon

I am going to rear gear to help keep temps down. I bought a 12 tooth pinion and a 56 tooth spur, which one will require the least amount of...

i have been planning on building a track below my zip line but it's been too wet at the site until today so i decided to break ground. still a ton of...

My first attempt at painting a body went fairly well. A couple small bleeds past the masking tape, a couple slightly thin areas, and two areas that I...

Ok guys i have a slash 4x4(backslash) i ran it at the track with the body on which has holes everywhere,i have the vxl fan,and a heat sink on the...

rpm bumpers and light bar and a rc-lights 12 led kit.

Hi, I was wondering what shocks you are running for racing. I will be running on a sandy track with sharp turns and a couple large jumps. Looking...

Found one at Hobby town USA today for 49 bucks. That matches Tower. So I picked it up. Works great. If they had more than 1 I would have bought...

I ordered 2 new ******* lipos and soldered on the Traxxas connectors. One battery works great. When I charged up and put in the other battery, I...

Well i decided that since i was hardly getting any runtime/really good speed i'd switch to lipo. So i went to my LHS, got a 3s 5000 mAh lipo battery,...

I just received my new center diff, and am so dismayed that the first few lines of instructions warn us to use off road only on 7 cell or 2S maximum....

wondering if anyone else can comment on these, I recently tried them and all I can say is WOW. I thought the stk shockes were ok, springs seemed a...

Any comment about this motors? does it can use on current original TRX esc?

hey guys, I currently have the hv pro 5.5 combo set-up, I wanna ditch the Novak controller, its big/bulky and i hate running a separate bec. I wanna...

in the pictures below you see the diff oils I have to use in the front and rear diffs. I cant seem to find 50K diff oil. team factory goes only from...

anybody used the rcscrewz bearing kit? i think i would like to upgrade/swap out my bearings sometime soon and i was wondering if that's a good way to...

It broke the right a-arm, and that was it. So I thought. I got it back together and ran it, but it was wasn't going very fast. It was slipping, like...

I know this has been asked many times before, I have searched and have not found a suitable answer. So please, can people post opinions and prefer...

I went to hobby shop to get some diff oil I wanted to get 5000wt for rear and 10000wt for front like in slayden setup but all they had was 3000wt and...

Howdy All, I purchased the rebuild kit for my 3500 motor since the front bearing sounded terrible after 6 runs. But the slash 4x4 motor looks...

What do you guys recommend for shocks and or springs for jumping? The stock ones seem to bottom out even on some small jumps.

ok i want to change my vxl motor and esc to the mmm will that motor be able to handle the 2s or 3s lipo and still keep cool

I recently bought a cooling fan for my esc and I think it works really well. I'm not sure what the normal operating temps of the VXL esc are but...