Forum: Slash 4X4

I had some extra cells laying around and I made up an 8 cell pack. I have had good luck with it. The stock esc and motor stay under 120f. It seems...

Anybody have any news on this bodyshell yet? I haven't heard anything for ages about it, has it been forgotten about or what??? :(

Hey y'all Thinking of getting a slash but always been into the revos and Tmaxx how many different slash versions are there ? witch 1 is the better 1...

Extremely sorry for the noob question, but I had never heard of CVDs until a few weeks ago. I have been trying to figure this out but can't. I...

I'm boiling some rims for the kids pedes and my wife walks in with a bday gift. She's supposed to be at work all night. It turns out the bday gift...

Here is a picture of my lightened slash chassis dyed Rose petal pink(rite dye).

hey guys. i did a backslash and used a hotbodies ve8 body and its a little to small for the chassis i dont like that it is showing the cjassi a lil...

I don't often post anything in the 4x4 section, but I thought I'd show off the body I painted up for my friend. It's a JConcepts Manta body, wing,...

has/is anyone using the new traxxas cvds for the slash 4x4 yet they look sharp. i have used them on my e maxx and had no problems at all.

How can I paint my stock shell? How should I do it and what are the preparation steps for it? Am I supposed to paint the inside of the shell? I...

I'm a tmaxx/erbe owner and I'm vacationing in myrtle beach...... Saw a pair of slash's in front of my suite. It was a guy and his gf...... Since...

I have a new pack that has slightly puffed and is ~.24 volts lower in one cell than the other after soldering on new ends. I think the pack got too...

As the title says I got a prepainted and trimmed sc10 body but it doesn't seem to fit well.. I flipped the front body posts around and it seems ok...

A lot of people are having bec problems with their mmp/novak 550's and im wondering what the bec is. Also how is the prpoer way to fix the bec...

I recently purchased some RPM body saver (snap washers) and they are slightly too large to fit through the openings in the body. What is the best way...

I have been lurking here for a short while and learned alot but have not seen a thread re this topic. While there have been quite a few lately around...

I have had enough of trying to mod the front hole of driveshaft, the fixes either dont work, dont last or cause binding when chassis flexes. I...

I know what your thinking,not another question of wich one is better,not this time.I need to know how the two compare to each other in physical...

Did a search, didn’t find too much info, so… I’m looking for a good set of tires for various surfaces & all around bashing. Any feelings on the...

I have 3 pedes and now a Slash 4x4 as of today. In my pedes I run 16/86 down from the stock 19 tooth pinion to keep the motors cooled as we run on...

When you switched to the MMM or Novak 4.5/5.5, was adding the extra weight to one side (right side) affect handling? I make a undertray that...

I have a new Slash 4x4 and it works fine with the stock battery and a 2cell lipo but when I hook up a 3cell lipo and give it gas the esc. just shuts...

Hey guys.. I have my 4x4 slash and put in my 8.5 Havoc pro in there and I get thermoed all the time. Even dropping the gearing down to 15T from...

i think i might of just set a speed record with my slash 4x4. i use'd this battery http://www.hobbypartz.com/83p-5000mah-6s1p-222-25c.html and this...

Slash 4x4 will engage motor and will not run wheels when I put car on ground. Is this the slipper clutch or diff?

Has anyone tested the difference in motor temps with and without the overtray? I am running a Neu motor(1509 1y smooth can 3600kv) and mmp esc on 2s...

i have a PE. at first, i had put too much threadlock into the steering hubs, so it would hardly steering to left/right. so i cleaned it up with...

my slash is 100% box stock. i was running 3s in a baseball diamond and it just stopped. no grinding sound or that firmilliar ripping sound of a...

Today my slash stopped running with the esc light blinking red, I assume it shut down due to overheating however the esc was not overheated, the...

which of the two big connectors will i get the most performance out of. I hear that the deans are better from most people. Also, the male plug is...